Datacomm 45 0031 Wh Recessed Voltage Receptacle (Ce Accessory) 3522

Review for datacomm recessed low voltage

Price was $25.63. Good quality and construction, if your scanner tells you there is something in the wall, there probably is. I checked with a drill bit, and it was hollow, but when i made a hole, there was a pipe inside and of course i had to move it over leaving a 4" gap.

-L. Kimberly

Datacomm recessed low voltage media plate duplex receptacle, datacomm electronics’ new, patented recessed low voltage media plate duplex receptacle offers the convenience of a duplex receptacle and a recessed plate enough room to store the -datacomm 45-0031-wh recessed low voltage media plate duplex receptacle, white

  • Special: Conceal Multiple Av Cables Behind Your Flat Panel Tv.
  • Special: 15 Amp/125 Volt Tamper Resistant, Duplex Receptacle (ul Listed Component).

Price Cut Datacomm 45 0031 Wh Recessed Voltage Receptacle (Ce Accessory) 45 0031 Wh

Buy Now

Preamble

A concern was all the reviews talking of the cheap plastic tabs on the brackets breaking off, the unit i received in aug 2013 had all metal tabs, which seem quite sturdy. The Best datacomm recessed low voltage as-of ( Nov 2018 ) | Datacomm Electronics-Ce Accessory Review Special Datacomm 45-0031-WH Recessed Low Voltage Media Plate with Duplex Receptacle, White Low profile design fits behind the industry's thinnest mounts and tv's. Conceal multiple av cables behind your flat panel tv. 15 amp/125 volt tamper resistant, duplex receptacle (ul listed component). Old work box included. Mounting wings are molded into the media plate and fasten tightly against the back of the drywall. quick & easy to install-no additional parts needed. .

Datacomm 45-0031-wh Recessed Low Voltage Media Plate With Duplex Receptacle, White Review (45 0031 wh)

First thing i noticed when i pulled this out of the box was its size. Installation is essentially just like an oversized low voltage gang box. . The good: it works, it's super easy to install and get wired up. . The indifferent: size. This plate is massive. Pay attention to how/where you plan to use this. I originally planned to have this sit behind/inside my tv mount so the cables could come out through the middle of it. This plate was larger than what was available so i had to mount it underneath. Fortunately, the tv was big enough to cover it. . *note* if mounting closer to a stud, pay attention as the recessed box that holds the outlet sticks way out. I had to make a mid-project adjustment to re-orient the whole thing 180 degrees in order to avoid a stud. -X. Yvette

Datacomm 45 0031 Wh Recessed Voltage Receptacle

  • Order: Electronics
  • Brand: Datacomm Electronics
  • Color: White
  • EAN: 0031112866567
  • Product Dimensions:
    Height:8.10 inches
    Length:3.50 inches
    Weight:0.75 pounds
    Width:7.50 inches
  • LegalDisclaimer: This Product Contains Chemicals Known To The State Of California To Cause Cancer And Birth Defects Or Other Reproductive Harm.
  • Manufacturer: DataComm Electronics, Inc.
  • Model: 45-0031-WH
  • MPN: 45-0031-WH
  • Total: 1
  • Quantity: 1
  • Part/Serial Number: 45-0031-WH
  • Sub-Type: Speakers
  • Category: CE ACCESSORY
  • Size: 45-0031
  • UPC: 660559008416
  • Warranty: 10-year

datacomm recessed low voltage media plate duplex receptacle, Speakers, Datacomm electronics' new, patented recessed low voltage media plate with duplex receptacle offers the convenience of a duplex receptacle and a recessed plate with enough room to store the low voltage cables behind your flat panel tv. Datacomm 45 0031 Wh Recessed Voltage Receptacle (45-0031-WH-Datacomm Electronics).

Datacomm 45 0031 Wh Recessed Voltage Receptacle Speakers

datacomm recessed low voltage Datacomm 45-0031-WH Recessed Low Voltage Media Plate with Duplex Receptacle, White (Switch to Mobile/Desktop Version)

Works perfectly as described. Looks good too. Wish i realized it was a 15amp outlet. Had to go and buy a 20 amp at the store in a pinch. My own fault for not reading the full description. Would recommend.

Datacomm 45-0031-wh Recessed Low Voltage Media Plate Duplex Receptacle, White
Click to see NoticeDatacomm 45 0031 Wh Recessed Voltage Receptacle (Ce Accessory)"This is a great option for neatly bringing power and signal wires to the back of a tv. . I installed mine on a seismic shear wall which has 1/2" drywall plus 1/2" osb sheathing behind it. With the mounting clamps unscrewed all the way to the retaining nut, they are able to accommodate a 1" thick wall without issue. . The outlet that comes with the unit is a basic tamper-resistant unit, but can be replaced with any standard decora outlet. I opted for a unit with built-in surge suppression (leviton 5280-w 15 amp, 125 volt, decora plus duplex surge suppressor receptacle, straight blade, industrial grade, self grounding, white) which fit fine and still had sufficient space in the box."


Featured Categories » Gold Merchants » Specialty Boutique » Datacomm 45 0031 Wh Recessed Voltage Receptacle (Ce Accessory) 45 0031 Wh


QualGear QG-TM-002-BLK 37-Inch to 70-Inch Universal Ultra Slim Low Profile Fixed Wall Mount LED TVs, Black

Mount style: fixed mount 37-inch to 70-inch product model : qg-tm-002-blk product color: black product description with an impressively ultra low mounting profile of just 0. 39-inch from the wall, the qualgear qg-tm-002-blk model is a super slim mount perfectly suited to complement your contemporary style and envy your friends and neighbors by showing off your flat tv installation. This mount supports most 37-inch to 70-inch flat panel tvs up to 66 lbs. This mount is part of the ultra low profile series of fixed mounts offering a sleek and slim design combined with easy installation. Tv compatibility check to check to see this mount works for your tv or monitor, please ensure your tv meets all of the checks specified below: 1. Size of tv: supports most 37 to 70-inch tvs. 2. Weight of tv: supports tvs that are weighing up to 66 lbs. 3. Mounting hole patterns (vesa) in mm: supports standard mounting hole patterns from 200x200 to 800x400. 4. Studs: supports both 16-inch and 24-inch most standard wooden stud spacings in the united states.   for walls that use wooden studs at 16-inch spacing, it is strongly recommended to mount this mount to 3 studs. Product features 1. Super slim design places tv just 0. 39 inches from the wall to enhance the look of ultra-thin led tvs 2. Spring-lock design enables easy display attachment and detachment 3. Direction indicators are marked clearly on the mount   4. Tv can be glided a few inches to left or right for perfect centering based on surroundings 5. Pre-sorted hardware pack for easy installation 6. Mounting hardware is included for mounting to wooden studs, concrete and brick surfaces

QualGear QG-TM-002-BLK 37-Inch to 70-Inch Universal Ultra Slim Low Profile Fixed Wall Mount LED TVs, BlackQualGear-QG-TM-002-BLK-37-Inch-70-Inch-Universal

QUALGEAR QG-TM-002-BLK 37-INCH TO 70-INCH UNIVERSAL ULTRA SLIM LOW PROFILE FIXED WALL MOUNT LED TVS, BLACK Overview
Brand :    qualgear
Color :    BLACK
Size :    37-70-Inch
Weight :    4.00 pounds
Model :    QG-TM-002-BLK
Quantity :    1
Order click here :    normally ships in 24 hours
  • Maximum weight capacity: 88 lbs
  • Supported mounting hole patterns (vesa): 200x200mm to 800x400mm
  • Supported tv sizes: 37" - 70"
  • Mount type: fixed
  • Mounting profile: 0. 4-inch from the wall
Price :    $29.95
Speakers :    Best Av Furniture (qualgear product review) for QualGear QG-TM-002-BLK 37-Inch to 70-Inch Universal Ultra Slim Low Profile Fixed Wall Mount LED TVs, Black available as-of ( Nov 2018 )

Bryant Electric RR1512W 2-Gang Recessed TV Connection Outlet Plate 15 Amp 125V Tamper-Resistant Duplex Receptacle One Pass-Thru Opening, White

Bryant provides multiple solutions for in-home av installations. With recessed plastic boxes and receptacles, low voltage cables and power cords are organized and protected. All wires stay hidden behind wall units and entertainment centers, allowing for a clean and flushed look. Products are offered in various color options to compliment or blend into any decor.

Bryant Electric RR1512W 2-Gang Recessed TV Connection Outlet Plate 15 Amp 125V Tamper-Resistant Duplex Receptacle One Pass-Thru Opening, WhiteBryant-Electric-RR1512W-Connection-Tamper-Resistant

BRYANT ELECTRIC RR1512W 2-GANG RECESSED TV CONNECTION OUTLET PLATE 15 AMP 125V TAMPER-RESISTANT DUPLEX RECEPTACLE ONE PASS-THRU OPENING, WHITE Review
Brand :    bryant electric
Color :    White
Size :    2 Gang
Weight :    0.2 pounds
  • Feed through brush covered opening conceals, organizes and protects low voltage cables in a/v and multimedia installations
  • Easily mounts to box with screws; use bryant netselect rr1500 for economical solution
  • Flush design fits behind wall mount flat panel tvs, a/v equipment, wall units/artwork/mounts
  • Ul listed and csa certified
  • Tamper-resistant duplex receptacle promotes safety and provides two 15a, 125v nema 5-15f power outlets
Price :    $8.00 (was $13.33)
Model :    RR1512W
Quantity :    1
Order click here :    normally ships in 24 hours
Home Improvement :    Best Home Lighting Accessory (bryant electric product review) for Bryant Electric RR1512W 2-Gang Recessed TV Connection Outlet Plate 15 Amp 125V Tamper-Resistant Duplex Receptacle One Pass-Thru Opening, White available as-of ( Nov 2018 )

KCC Industries 1-Gang Recessed Low Voltage Cable Plate Mounting Bracket 2-Pack, White

Kcc industries 1-gang recessed low voltage cable plate with mounting bracket (2-pack, white) cable plate designed to provide a clean look to passing low voltage cables through wallsholds a multitude of different chords (phone, internet, tv, video)crafted from premium abs plastic with a smooth white finish to blend with other wall plates in your homemounts easily to the included mounting brackets with mounting screws includedcan be installed with opening facing up or downouter dimensions: 2. 75 in. W x 4. 5 in. H low voltage mounting bracket easy to install and designed specifically for passing low voltage wires (phone, internet, tv, video) through a wallhas oval mounting holes that allow for final shifting and straighteningadjusts to fit various wall thicknesses (1/4" - 1"), as the bracket wings secure when mounting screws are tightenedacts as its own template for cut-out; simply trace the inside of the bracket then cut the holeul/csa listed and provides added protection for cables that run through knockouts in metal studs included in package: 2x cable plates w/ mounting screws 2x low voltage mounting brackets 1x mounting instructions kcc industries is a veteran-owned business, and we offer a 100% satisfaction guarantee. Items come with a 1 year replacement warranty, and if you are not completely satisfied with your purchase within 90 days, send it back for a full refund - no questions asked!

KCC Industries 1-Gang Recessed Low Voltage Cable Plate Mounting Bracket 2-Pack, WhiteKCC-Industries-Recessed-Voltage-Mounting

KCC INDUSTRIES 1-GANG RECESSED LOW VOLTAGE CABLE PLATE MOUNTING BRACKET 2-PACK, WHITE Features
Brand :    kcc industries
Color :    White
Size :    1-Gang
Model :    SG1-WH
Quantity :    1
Order click here :    normally ships in 24 hours
Speakers :    Best Ce Accessory (kcc industries product review) for KCC Industries 1-Gang Recessed Low Voltage Cable Plate Mounting Bracket 2-Pack, White available as-of ( Nov 2018 )
Price :    $14.95
  • Satisfaction guarantee - kcc industries is a veteran-owned business, and we offer a 100% satisfaction guarantee. items come with a 1 year replacement warranty, and if you are not completely satisfied with your purchase within 90 days, send it back for a full refund - no questions asked!
  • Organize cables - the perfect solution for concealing up to 4 low voltage audio/video cables behind your wall-mounted flat panel tv (may hold more than 4 cables depending on type)
  • Easy install - simply trace the inside of the bracket onto your wall, cut it out, and install the bracket and cable plate. cable plate can be installed with opening facing up or down
  • The perfect match - these cable plates and brackets have been tested and paired in multiple applications and are a guaranteed fit!
  • Safety certified - mounting bracket is ul/csa listed for class 2 low voltage cables (not rated for passing ac power chords)

Leviton 689-W 15 Amp 1-Gang Recessed Duplex Receptacle, Residential Grade, Screws Mounted to Housing, White

The leviton recessed boxes install invisibly behind wall units, wall-mounted flat panel tvs, monitors and signature artwork. They are perfect for homes, apartments, co-ops, condominiums and offices. 15 amp 1-gang recessed duplex receptacle, residential grade, with screws mounted to housing, white.

Leviton 689-W 15 Amp 1-Gang Recessed Duplex Receptacle, Residential Grade, Screws Mounted to Housing, WhiteLeviton-689-W-Recessed-Receptacle-Residential

LEVITON 689-W 15 AMP 1-GANG RECESSED DUPLEX RECEPTACLE, RESIDENTIAL GRADE, SCREWS MOUNTED TO HOUSING, WHITE Spotlight
Brand :    leviton
Color :    White
Size :    N/A
  • Fits most common electrical boxes
  • Offers a ul approved, code-compliant solution providing two 15a/125vac nema 5-15r power outlets
  • Supplies ac power for two components (flat panel tvs and video receiver)
  • Flush-mounted to install invisibly behind wall units, wall-mounted flat panel tvs and signature artwork
  • Perfect in homes, apartments, co-ops, condominiums and offices
Price :    $3.32 (was $8.21)
Model :    689-W
Quantity :    1
Order click here :    normally ships in 24 hours
Home Improvement :    Best Home Lighting Accessory (leviton product review) for Leviton 689-W 15 Amp 1-Gang Recessed Duplex Receptacle, Residential Grade, Screws Mounted to Housing, White available as-of ( Nov 2018 )

DataComm Electronics 45-0002-WH 2-Gang Recessed Low Voltage Cable Plate, White

Datacomm electronics 2-gang recessed low voltage cable plates are used to install low voltage cables behind your flat panel tv, amplifier, or other audio and video devices. These plates are designed to be installed onto a low voltage mounting bracket. The cable plates can be installed with the opening facing up or down.

DataComm Electronics 45-0002-WH 2-Gang Recessed Low Voltage Cable Plate, WhiteDataComm-Electronics-45-0002-WH-Recessed-Voltage

DATACOMM ELECTRONICS 45-0002-WH 2-GANG RECESSED LOW VOLTAGE CABLE PLATE, WHITE Pros
Brand :    datacomm electronics
Color :    White
Size :    2 gang
Weight :    0.22 pounds
  • Made of non-breakable abs plastic
  • The perfect solution for concealing low voltage audio video cables behind your wall mounted flat panel tv
  • Available in 4 colors
  • Can be installed with the opening facing up or down
  • Etl listed in the united states and canada
Price :    $3.46 (was $5.29)
Model :    45-0002-WH
Quantity :    1
Order click here :    normally ships in 1-2 business days
Speakers :    Best Ce Accessory (datacomm electronics product review) for DataComm Electronics 45-0002-WH 2-Gang Recessed Low Voltage Cable Plate, White available as-of ( Nov 2018 )

DataComm Electronics 45-0003-WH 3-Gang Recessed Low Voltage Cable Plate, White

Datacomm electronics 3-gang recessed low voltage cable plates are used to install low voltage cables behind your flat panel tv, amplifier, or other audio and video devices. These plates are designed to be installed onto a low voltage mounting bracket. The cable plates can be installed with the opening facing up or down.

DataComm Electronics 45-0003-WH 3-Gang Recessed Low Voltage Cable Plate, WhiteDataComm-Electronics-45-0003-WH-Recessed-Voltage

DATACOMM ELECTRONICS 45-0003-WH 3-GANG RECESSED LOW VOLTAGE CABLE PLATE, WHITE Reviews
Brand :    datacomm electronics
Color :    White
Size :    3 gang
Weight :    0.25 pounds
  • The perfect solution for concealing low voltage audio video cables behind your wall mounted flat panel tv
  • Made of non-breakable abs plastic
  • Available in 3 colors
  • Etl listed in the united states and canada
  • Can be installed with the opening facing up or down
Price :    $1.60 (was $7.72)
Model :    45-0003-WH
Quantity :    1
Order click here :    normally ships in 24 hours
Speakers :    Best Power Supplies Or Protection (Speakers product review) for DataComm Electronics 45-0003-WH 3-Gang Recessed Low Voltage Cable Plate, White available as-of ( Nov 2018 )

IMBAPrice LV1-2PK Single Gang 1-Gang Low Voltage Mounting Bracket - Black Pack of 2

Low voltage mounting bracket, 1-gang, black, 1-pack. Mounting bracket has oval holes that allow final shifting and straightening. Easy to install, for mounting low voltage wires(phone, internet, tv, video). Adjusts to fit various wall thickness, the bracket wings secure when mounting screws are tightened. Bracket is its own template for cut-out, trace the bracket then cut the hole, includes 1 low voltage mounting brackets. Horizontal or vertical mounting, installs faster and costs less than metal brackets, ul/csa listed. Protects cable as it runs through the knockouts in metal stu

IMBAPrice LV1-2PK Single Gang 1-Gang Low Voltage Mounting Bracket - Black Pack of 2iMBAPrice-LV1-2PK-Voltage-Mounting-Bracket

IMBAPRICE LV1-2PK SINGLE GANG 1-GANG LOW VOLTAGE MOUNTING BRACKET - BLACK PACK OF 2 Spotlight
Brand :    imbaprice
Color :    Low Voltage Mounting Bracket
Size :    1 Gang (2 Pack)
Model :    LV1-2PK
Quantity :    1
Order click here :    normally ships in 24 hours
Ce :    Best Office Electronics (imbaprice product review) for IMBAPrice LV1-2PK Single Gang 1-Gang Low Voltage Mounting Bracket - Black Pack of 2 available as-of ( Nov 2018 )
Price :    $6.19 (was $6.29)
  • Ul/csa listed
  • Horizontal or vertical mounting
  • Adjusts to fit 1/4-inch to 1-inch thick wall board, paneling or drywall
  • Single gang (1-gang) low voltage mounting bracket - black (pack of 2)
  • Designed to mount wall plates flush

DataComm 45-0001-WH 1-Gang Recessed Low Voltage Cable Plate White

This worked great for running av to my flat screen wall mounted tv. I liked the 3-gang a little better than a 2 as i was able to open a bigger hole to see what was going on in the wall. I mounted my tv over a direct vent fireplace and this three gang allowed me to make sure i was strapped to a stud and greater than 2 feet in all directions from the fireplace. Overall it worked great. I was able to get my arm in the wall and move around much better than a 2-gang would have let me. . For those that were talking about how to mount this to the wall, i think people don't realize that you should be using a mounting bracket with these. These are intended to go over a 3-gang box or low voltage mounting plate. If you don't have one, i picked up one and it mounted right to the drywall with ease and you don't have to worry about pulling it out. The reason it comes with the "flat screws like a light switch" as one reviewer put it is because it's designed to be installed like a light switch, not directly into drywall. . If you need a low voltage mounting bracket: vanco lv3 pvc low voltage mount brackets (triple). . I also uploaded a few pics if you need clarification. . The only downside to be aware of is this does open up a large hole in the wall. Make sure you aren't creating a huge draft situation. I used a little cotton insulation (i would advise against fiberglass since it's exposed) and it stopped the draft. If you're worried, light a match and blow it out right in front of the plate, if the smoke goes straight up, you're good.

Datacomm electronics 1-gang recessed low voltage cable plates are used to install low voltage cables behind your flat panel tv, amplifier, or other audio and video devices. These plates are designed to be installed onto a low voltage mounting bracket. The cable plates can be installed with the opening facing up or down.

DataComm 45-0001-WH 1-Gang Recessed Low Voltage Cable Plate WhiteDataComm-45-0001-WH-1-Gang-Recessed-Voltage

Datacomm 45-0001-wh 1-gang Recessed Low Voltage Cable Plate White (45 0001 wh) FAQ.

Purchased this item along with the arlington tvb613bl-1 recessed tv 4-gang outlet box so that i could hide the cables running up from the back of my entertainment stand & up to an articulating wall mount & behind my tv. . Installed this item down low, behind the entertainment stand, and it was more than able to handle the bundle all of my cables, which were fed up to & separated at the 'arlington' outlet box installed next to the articulating tv mount. I had chosen the arlington style box for a 'cleaner' look behind the tv, because i am using an articulating wall mount where the cable exit point could be easily seen when the tv was extended away from the wall, but if your application is for a fixed mount, i would recommend getting two of these mounts (one for each end). . All in all, a great little product that makes for a 'clean' looking job. -Notice from L. Morgan, Salford

Click to Show datacomm 45-0001-wh 1-gang recessed low voltage cable plate white (45 0001 wh) Details

I ordered these and they worked perfectly! only thing is i didnt know it didnt come with the wall mount plates that were sold separately so to finish up my little project i had to improvise lol but these worked so perfectly for what i needed them to. I used one for the ceiling for my projector and two for the wall with a bunch of coaxial cables and one for my brothers room to run a cat 5 cable that was over 100' long run lol

Datacomm-45-0001-wh-1-gang-recessed-low-voltage-cable-plate-white-(45-0001-wh) set picture

- U. AnonymousI mounted a tv on the wall of my kitchen and was looking for an inexpensive way to hide the wires. This is ideal. . It's simple to install. You just need two of these and two low voltage brackets like this: arlington lv1-1cs single gang low voltage mounting bracket device you use a stud finder to make sure you're not looking to put this in a stud, and then use a drywall saw to cut the hole. Repeat to put the one down below. (use a level to ensure they're straight. ) insert the low voltage mounting bracket in both the upper and lower and then put the plate on the upper one. Start fishing cables through the wall. (it's easier to leave the plate off the lower one until you fish all the wires out of the wall first. ). . Through a one-gang plate, i have an hdmi cable, a vga cable, a set of composite cables with sound, a 1/8" headphone jack cable, and a network cable. It's tight, but everything fits. . Order these plates. You won't be disappointed.

What can you really say about a cable plate? apparently enough to warrant a review! this is the item you need to finish off your wall-mount tv installation. I purchased two of these, one to go behind the tv, and the other at the level of the power outlet below. It's easy as pie.

R. Anonymous, Newfoundland and Labrador

DATACOMM 45-0001-WH 1-GANG RECESSED LOW VOLTAGE CABLE PLATE WHITE Summary
Brand :    datacomm electronics
Color :    White
Size :    1 gang
Weight :    0.14 pounds
Model :    45-0001-WH
Quantity :    1
Order click here :    normally ships in 24 hours
Speakers :    Best Ce Accessory (datacomm electronics product review) for DataComm 45-0001-WH 1-Gang Recessed Low Voltage Cable Plate White available as-of ( Nov 2018 )
Price :    $2.00 (was $3.96)
  • Can be installed with the opening facing up or down
  • The perfect solution for concealing low voltage audio video cables behind your wall mounted flat panel tv
  • Holds up to 4 cables
  • Available in 5 colors
  • Made of non-breakable abs plastic

Buyer's Point Brush Wall Plate, Single Gang Low Voltage Mounting Bracket Device White Kit

"brush wall plate blends in and makes it easy to neatly run cables & wires through the wall" cables & wires don't need to cause a mess it's now possible to keep your home looking clean and tidy, without cables running everywhere - but still enjoy a top notch hdtv or home theatre system. With your new brush wall plate insert, you can quickly and easily run all cables through the wall without making a mess. Works with all cable types run hdtv cables including hdmi, coax cables, all audio/visual wires, phone, internet, or other networks cables easily through this single brush outlet cover. Whether you're setting up an hdtv or a complete home theatre system, this discreet cable access port has got you covered. Matches your home decor this cable access strap is white/ivory to coordinate with the existing color scheme of most homes. Light switch and socket plates are generally the same color, so your gang cable plate will blend in perfectly. Easy to install kit includes low voltage mounting bracket included for easier install. The brush wall plate is as easy to install as any regular socket wall plate - all you need is a standard screwdriver. Simply affix the brush insert to the outer casing, screw in the four screws and you're good to go! don't wait to order the brush wall plates you need today! click "add to cart" now to have your brand new white brush wall plate insert rushed directly to your door!

Buyer's Point Brush Wall Plate, Single Gang Low Voltage Mounting Bracket Device White KitBuyers-Point-Voltage-Mounting-Bracket

BUYER'S POINT BRUSH WALL PLATE, SINGLE GANG LOW VOLTAGE MOUNTING BRACKET DEVICE WHITE KIT Feature
Brand :    buyer's point
Color :    White Kit
Weight :    0.2 pounds
Model :    1018
Quantity :    1
Order click here :    normally ships in 24 hours
  • Easily run cables through wall, single brush wall plate easily creates cable access from any wall.
  • All cable types, gang cable access strap works perfectly with hdmi cables, coax, audio speaker wires
  • White/ivory color matches your home, socket plate allows you to match your wall plates in your home
  • Included new model - no gap low-voltage mounting bracket for easy installation
  • Smooth and clean hdtv installations, perfect for hdtv cables and home theater installations
Price :    $6.77 (was $8.97)
Speakers :    Best Ce Accessory (buyer's point product review) for Buyer's Point Brush Wall Plate, Single Gang Low Voltage Mounting Bracket Device White Kit available as-of ( Nov 2018 )

Arlington LV2 Low Voltage Mounting Bracket, 2-Gang, 2-Pack

Arlington lv2-1cs double gang low voltage device. Arlington's non-metallic, lv2-1cs, low voltage mounting brackets are the time and money-saving solution for faster and easier mounting of class 2 communications, computer and cable tv wiring. The bracket is its own template. Level the bracket on the wall. Then use the bracket a s a guide for the cut out by tracing a line around the inside. Arlington fittings are carefully inspected and our manufacturing process is designed to prevent the possibility of a defective product leaving our plant. In the event any of our products are found to be defective, we will replace them with new product free of charge. The time limit for this warranty is one year following the date of sale or one year after the date of installation, whichever is the earlier date. This warranty does not apply when the product is used for any purpose other than the intended use as described in the arlington literature. This warranty does not apply when the product is used for any installation which would violate the national electrical code or any code which takes precedence in a particular jurisdiction. Labor is not included.

Arlington LV2 Low Voltage Mounting Bracket, 2-Gang, 2-PackArlington-Voltage-Mounting-Bracket-2-Gang

ARLINGTON LV2 LOW VOLTAGE MOUNTING BRACKET, 2-GANG, 2-PACK Review
Brand :    arlington industries
Size :    2-Pack
  • Adjusts to fit 1/4 inch to 1 inch thick wall board, paneling or drywall
  • Mounting brackets offer specially designed screw holes, for a better looking, easy to install job
  • Save when you buy the 2 pack! designed to mount wall plates flush
  • Horizontal or vertical mounting; ul/csa listed
  • Designed to mount wall plates flush
Price :    $7.39 (was $7.59)
Model :    LV2-1CS/PACK
Order click here :    normally ships in 24 hours
Home Improvement :    Best Home Lighting Accessory (arlington industries product review) for Arlington LV2 Low Voltage Mounting Bracket, 2-Gang, 2-Pack available as-of ( Nov 2018 )

datacomm 45-0031-wh recessed low voltage media plate with duplex receptacle, white Price : 18, was : 25.63 as 2018-06-28
USUKDEFRESITJPCNCAGlobal
United States
Great Britain
German
France
Spain
Italy
Japan
China
Canada
World Wide
Datacomm 45 0031 Wh Recessed Voltage Receptacle (Ce Accessory) Reviewed by on ziwus.com

Top datacomm 45 0031 wh recessed voltage receptacle (ce accessory) Content

The F.A.Q. for datacomm 45-0031-wh recessed low voltage media plate with duplex receptacle, white

Let me say first off there are some misconceptions about this plate based on the "most helpful" reviews that are older:. . - the locking tabs are made out of metal now and are no longer plastic. - the plate itself is made out of a very sturdy plastic and does not feel cheap. - you can install this on an outer wall that has insulation, just takes a bit of work. - no issues with crosstalk/interference from low and high voltage wiring using standard shielded cabling (ran parallel). . I used this for wall mounted tv and it worked great. I ran the following wires through the opening with room to spare:. . - hdmi x2. - optical. - component a/v. - ir extender (1/8" style cabling, similar to what is used for headphones). - wii sensor bar extender cable. - 16 gauge speaker wire. . I would recommend changing the outlet with a leviton surge protected outlet (or similar product) if you do not have another option for surge protection, that is, an option that won't leave your setup looking like crap. You will need roughly 7 1/4 and 7 3/8" rectangular (not a perfect square) cut out based on template, but i would plan on 8 inches plus a few more inches on the electrical receptacle side as it goes into the wall at an angle. . I really hate seeing this product getting stars knocked off of it because it is "to big" and the buyer didn't provision correctly to ensure it would fit into the allotted space. This is a really great product for clean looking wall mounted tv installations - just make sure you have the room for it.

A number of questions have been asked here.

Q&A

(0) Question: Does this come with the top (for the tv) and bottom outlet (that plugs into an existing outlet)? or do i have to buy a separate bottom outlet?


(1) Question: Will this fit in a standard 2 gang electrical box? looks like the angle on the outlet would prevent that. 3 gang needed?


(2) Question: If mounted directly to drywall (not studs), is a low voltage mounting bracket needed?


(3) Question: Are the 120volts conductors completely enclosed in a box, as per the nec?


(4) Question: Can i install it 45 to the right, to allow the opening for wires to drop in from above?


(5) Question: How much depth is required to install this?


(6) Question: Is this gfci or surge protected or neither? do i need either for tv? wouldn't want my tv to get cooked


(7) Question: We bought this and now we missplaced the electical plug insert part. can we buy the proper one separately?


(8) Question: What's the best way to fish wires from the top receptacle (behind tv) to the bottom receptacle (av equip)? just dangle from top?



(note) Question: where/how to get Datacomm Electronics (manufacturer's brand) accessories & similiar Datacomm Electronics's products

Answer:

Click the marked text to copy link to Clipboard

Easy to install, holds securely to the wall, thick durable plastic that will hold up to the low demand on the product. It is fairly large which might make it difficult to install some tv mounts around it, however it did fit just barely inside of the mount i was using. The opening is large without being obtrusive, had it installed in about 15 min, wired and all. . Also, the outlet that comes with it is not gfi (not that it needs to be), and it has the child safety built in.


Accessories & Supplies 704182, Audio & Video Accessories 235271, Distribution 13914011, Electronics 282271, Wall Plates & Connectors 14024011Top Datacomm 45 0031 Wh Recessed Voltage Receptacle (Ce Accessory) FAQ Content

Best datacomm 45 0031 wh recessed voltage receptacle (ce accessory) in review

Does a great job, exactly what i wanted. I had never wired outlets before but with some research i was able to add one of these behind my tv and another on in my pantry. This comes with the outlet and box to house the wires in. You cut the hole (template included and then place in in hole, it has clips that can be tightened to hold it to the dry wall. Tip: i would install in a inch or two of the stud. The outlet that it comes with only has the pushing wire receptacles for the white and hot. There are 4 hole for each. Then the ground is a green screw on the side. I was easily able to add from existing outlet then add a second one off the new one. Will but again when i need another one.

Z. Angela, Alaska

You might like to see 160 Led Cn-160 Dimmable Ultra High Power Panel Digital Camera / Camcorder Video Light, Led Light Canon, Nikon, Pentax, Panasonic,sony, Samsung Olympus Digital Slr Compatible Battery (not Included): Aa Ni-mh Or Alkaline Battery; Panasonic Sd Series Li-ion Batteries; Sony Li-ion Battery Fh, Fm And F Models. Note: Sony Fw Series Battery Can Not -Neewer 160 Led Cn-160 Dimmable Ultra High Power Panel Digital Camera / Camcorder Video Light, Led Light Canon, Nikon, Pentax, Panasonic,sony, Samsung Olympus Digital Slr Cameras
  1. Attribute: There Are 2 Filters Included With This Item, With Spotlight Effect, Diffuse Effect, And For Reducing The Color Temperature To 3200k.
  2. Attribute: The Light Intensity Can Be Changed To Offer Professional Effects.
Low-End Dimmable Digital Camcorder Panasonic Samsung (Camera Other Accessories) 40004082 Dimmable Digital Camcorder Panasonic Samsung
Or you might like to consider Carry bag portable satellite the king cb1000 portable satellite antenna carry bag protects and stores your king tailgater or quest antenna when not in use. convenient features include a zipper closure, carry handles, -king cb1000 carry bag portable satellite antenna
  • Spotlight: Carry Handles And Backpack Straps.
  • Spotlight: Internal Storage Pockets For Satellite Receiver, Remote Control, And Cables.
Shopping King Cb1000 Carry Bag Portable Satellite Antenna (Auto Accessory) Cb1000 King Cb1000 Carry Bag Portable Satellite Antenna (Auto

O. Colleen, Shropshire says

I wanted to mount a tv on the wall of by bedroom. I found this and decided to give it a try. It was much easier than i thought it would be. I measured for the mount and then determined where to locate the recessed plug. I used the template provided to draw the cutting path and a drywall saw to cut the hole. In my application i had an active socket directly below the wall mount so i connected my romex to the existing outlet and passed the wire up behind the wall to the new hole. I made the connections to the new plug, and mounted the provided junction box to the recessed frame. Once that was complete i fixed the recessed frame to the wall, leveled it and tightened the screws against the tabs which secure the fixture against the drywall. I had read reviews that suggested the tabs were flimsy and easily broken. This was not my experience. The tabs seemed fine and secured firmly. Once the unit was installed and i successfully tested the circuit, i was ready to install the wall mount for the tv. I used the mount found here: . This mount overlaps the edges of the recessed plug, but that was no issue. I did not have need of the cable run, but was able to tuck away excess power cable in the opening. If this is installed properly and cleanly, it actually looks very good. If not, it is at least it covered by the tv. I would recommend this to a friend.

W. Reed, Kensington and Chelsea

This thing is very solid, affordable and easy to install. I have become a fan of datacomm solutions because of this. Highly recommended. Please make sure to take into account the dimensions of this solution since it maybe a bit large and difficult to hide if your tv is smaller than 47'.

O. Cathy, Tower Hamlets says

It is much larger than it looks in the pictures. The hole for the low-voltage cables is large enough for anything i could imagine. It is totally open so i sealed it off with a piece of styrofoam cut to fit. Installation was easy, however, the electrical box is a bit odd since it has to be completely wired and assembled before the whole piece can be inserted into the wall. The swivel flanges that hold it to the sheetrock are all metal and plenty strong enough.

V. Jacqueline, Australian Capital Territory

For the money this thing rocks. I was looking to clean up the install of 2 of my flat screens and the kits at my big box store were twice the cost. I tried one of these and loved it so much i ordered a second one. It is plastic, the outlet is not a surge protected one although you can buy one and put it on here and it installs easily. Yes once again it's plastic so if you are rough you can crack it, but i installed two with zero issues. I highly recommend.

K. Shayna, North Tyneside says

I purchased this to mount behind my tvs and hide cables. I would buy it again. . Pro:. It was very easy to install, works as advertised. . Con:. The outlet that is provided doesn't have typical screws for the wiring like other outlets, instead it has little holes. My house is wired with brand new romex 12/3 and the wires wouldn't fit in the holes. I was unable to use the outlet. Fortunately i have an abundance of standard decora outlets laying around and was able to simply substitute it for one that worked.

A. Newell, Thueringen

Allowed me to install my tv on a false wall. Just what i was looking for. . Only tip is the flip out anchors don t always latch into the wall, i was lucky enough my wall is false so i could see this happened

D. Anonymous, Western Australia says

I bought 3 of these (for 2 rooms) to mount behind my tv and media table. It comes with template to trace onto the drywall, but i think i just took measurements and used my square to trace out the cutout area. It was really easy to install and looks great on the wall. It fits flush and tight and i love it for the fact that it's retrofit and i can remove it at anytime to pull more cable into the wall (if need be) and into the box. I'd definitely recommend to anyone that needs it for a similar purpose.

S. Gloria, Wokingham

This is a great way to make a clean installation for all those hdmi, power and speaker wires you don't want to look at. One piece of advice though, be sure that you also order the brackets that these screw into. Otherwise you will be doing what i did and using wood or sheet rock screws to hold them to the wall and painting the screw heads. It's not obviously stated on online store that you need the mounting frames for a proper install. I also purchased the 1 and 2 gang data outlets as well. All great products.

P. Donna, Sunderland says

Works great for behind a wall mounted tv. You are required to cut a 7-1/8 x 7-1/4 inch hole in the wall. That allows you easy access to stick your arm down in the wall to pull up wires. Note that the unit does not mount on any studs. In fact the left hand side of the unit needs to be about 3 inches to the right of a stud (see picture). This is because the ac electrical box protrudes to the left of the unit behind the wall. The ac outlet is just a normal outlet, no surge protection of ground fault protection on this model (other models have surge protection). If you want to add surge protection, a simple, cheap solution is this: belkin surgecube surge protector with 1 outlet it fits nicely (but it covers up one of the outlets) (see piciture). Installation instructions can be found searching google for "datacomm 45-0031". Note that only the first 2 pages of the instructions are for this unit. The other pages are for different model numbers.

J. Erin, Colorado

These things are a great idea. I had two powered wall mounted studio monitors and everything now enters above my wall mount brackets. No more dangling wires. Everything is neatly behind the wall. But as always, they are made with cheap plastic and hardware.

L. Alba, Baden-Wuerttemberg says

I just installed two of these wall plates 1/30/16. Very happy with the way install went, the only surprise i had was that is for 14 guage wire. Not sure if i over looked that in the descripting or not, but i was surprised. Both plates had metal wings and they operated very smoothly. The outlets themselves have those safety inserts that require a lot of pressure to get the plug in the socket. In terms of the dimensions, i did a 7" x7" square and then did extra trimming of the sheetrock as needed. It ensured a snug fit. The only thing i would change about the product is i with there was something to close the gap that you run the video cables through. I'm not a big fan of leaving an opening between my room and the inner wall. I'll be cutting a little foam to close the cresent moon gap.

H. Eleanor, Rheinland-Pfalz

This is the second recessed media plate i've purchased from datacomm - their products are of great quality and are a must have for any wall-mounted tv, its amazing what a difference it could make to have no cables hanging down. . It is definitely a time consuming install project if 1) it is your first time and 2) you are installing this on an exterior wall that is filled with insulation, but you quickly get the hang of it after the initial trial and error.



Leave a Reply

You must be logged in to post a comment.


Top datacomm recessed low voltage Review Content

Related Products

Product Image Gallery

Top-datacomm-45-0031-wh-recessed-voltage-receptacle-352204gz89n0-Content